BEIYANG BTP-2200E USB DRIVER

0 Comments

Please do not change them. It is the first time to mount and use the printer; The printer is used again after a long idle time; Replace new type of paper roll; First time to use it after cleaning the sensor; Fails to identify marks in effect during the print; Operation environment of the printer is changed greatly. The installation method of the driver: When data is transmitted, the host should not ignore Busy signal, otherwise it could cause the print data lost; Parallel interface signal uses TTL level. Figure G shows the tear-off position upwards, which should be adjusted in negative direction; Figure H shows the tear-off position downwards, which should be adjusted in positive direction; 4 Routine maintenance of the printer Follow the steps as below to clean the THP, platen and sensor monthly.

Uploader: Temi
Date Added: 2 November 2005
File Size: 51.43 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 76846
Price: Free* [*Free Regsitration Required]

When loading the paper, please put the label mount through the peel-off module according to the process as below: It is the first time to mount and use the printer; The printer is used again after a long idle time; Btp-2200r new type of paper roll; First time to use it after cleaning the sensor; Fails to identify marks in effect during the print; Operation environment of the printer is changed greatly.

It can apply to real-time label printing, label batch printing, transport and us label printing, other receipt printing for railway, airport, bus station, etc.

If it is normal the Printer can continue to work, otherwise please replace the THP test page is referred to Appendix 1 Print darkness is too high Operation environment temperature is too high, the THP is overheated. In beijang print, follow the pressure level of factory default settings, normally at level 2 or 3.

  FOXCONN 865M01-G-GLS DRIVER

SNBC BTPE BPLE Printer Drivers – Download Device Drivers – –

If this THP still fail to work properly, please contact with our distributor or manufacture. When connecting USB interface printer to the host, the system identifies USB device automatically and pop up the driver installation guide. If briyang problem still cannot be removed, please contact with our distributor or manufacturer.

If they are different, please correct and print it again.

Beiyang Printer Btpe Suppliers, all Quality Beiyang Printer Btpe Suppliers on

Top cover of sensor Figure 3. Adjust the printout in vertical direction with 1 dot as a motion unit. If users need the further data about these products, please feel free to contact our market department or your local distributor. Self-test page sees appendix 1 ; 2 3 The configuration describes the current settings of the printer.

The installation method of the driver: The configuration information and internal font presents the current settings of the printer. Adjust the printout in horizontal direction with 8 dots as a motion unit. If it is the marked paper, please put black mark downwards; The front end of paper veiyang should be in the middle of the platen as possible as it can. The printer shall restart Auto checkout. Print pattern hall not move when it is less than 4 dots, or the print pattern shall bpt-2200e based on 8 dots when it is between 4 dots and 8 dots.

When using it, ensure that up and down time of host signal is less than 0. A Btp-220e0 sensor 1 2 3 4 Turn off the printer and open top cover; Lift up the print mechanism and press on the latch to open the paper-pressing module; Clean away dusts or dirt on the transmission sensor with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover.

  EDIROL PCR-800 WINDOWS 7 DRIVER

Figure D shows the print position towards left, which should be adjusted in positive direction; Figure E shows the print position towards right, which should isb adjusted in negative direction.

B Auto Checkout functions Before starting the print job, the printer shall compare the parameter set by customers with current parameter of the printer to decide if it shall initiate the checkout with the process as below: The printout is not clear; Noise in paper feed vtp-2200e retraction is much; Dusts udb on the platen.

If any part is short or damaged, please contact with our distributor or manufacturer. Trademark Our registered trademark Safety warning Caution: Power LED always light. Check the THP test page is Normal until its temperature is down.

BTP-2200E Barcode printer,Direct thermal, 203dpi,Free shipping

It shall enter pause status after success. Drop paper roll on the paper holder to the paper room, then pull out the front end of the paper and put it in the print path flatly, and also release the paper guide to hold it.

The printer finds out USB device drive path and installs this driver depending on this guide. When the printer identifies that Auto checkout is needed, the printer shall feed two or three labels for checkout.

In case that this happens, turn off the power immediately. Select the print mode: Beiysng comply with warning to avoid bodily harm or damage to device Notice: